Shanghai Clirik Machinery Co., Ltd

Three-ring medium-speed micro-grinding can be through the fine processing of the material, the material grinding to more than 3000 eyes of ultrafine granularity, is the market processing of ultrafine powder commonequipment. Three-ring medium-speed micro-grinding is a kind of fine powder and ultra-fine powder processing equipment, the application of a number of national new mill patented technology, the design of novel, reasonable structure, small footprint, low power consumption, long operating life, and low cost-effective consumables of consumables. Its technical performance has reached the international leading level, this micro-grinding is mainly applicable to medium and low hardness, Mohs hardness less than 6 levels of non-flammable and explosive various brittle materials, such as calcite, chalk, calcium carbonate, dolomite, kaolin, bentonite, bentonite, talc, mica, diamond magnesium, Yili, leaf stone, zircon, sea foam, concave rod rod, Retostone, diatom, heavy crystal, gypsum, alumite, graphite, fluorite, phosphorus ore, potassium ore, flotsam, etc. It can be used as a desulfurization mill and dolomite grinder.
At present, the fine powder finished product of the three-ring medium-speed micro-grinding is adjusted arbitrarily between 325-3000 targets, with a yield of 0.5-12 tons per hour.

Three-ring medium-speed micro-grinding performance

1, high product fineness is a significant feature of the three-ring medium-speed micro-grinding, fineness can reach D97 , 5 m at once.

2, cleaning and environmental protection is the three-ring medium-speed micro-grinding for several years of widespread application of the reason, the use of pulse dust collector to capture dust, the use of mufflers to reduce noise, with the advantages of clean and environmental protection.

3, high efficiency and energy-saving so that the three-ring medium-speed micro-grinding in the finished fineness and motor power of the same case, than the air flow grinding, stirring grinding, ball mill production is more than double.

4, high safety and reliability, because the three-ring medium-speed micro-grinding in the grinding cavity without rolling bearings, no screws, so there is no bearing and its seal softened problem, there is no screw easy to loosen and destroy the machine.
5, the long service life of the consumables, three-ring medium-speed micro-grinding rollers, grinding rings made of special materials, in the same material and finished product fineness, than the impact crusher and turbine shredder wear parts life of 2-5 times longer, generally up to more than one year, processing calcium carbonate, square solution stone, the service life of up to 2-5 years.

Structural composition of three-ring medium-speed micro-grinding

The full set of configurations of ultra-fine grinder includes hammer crusher, bucket lifter, storage silo, vibration feeder, micro-grinding host, variable frequency grader, double-link cyclone dust erlot, pulse dust removal system, high-voltage fan, air compressor, electrical control system.

Precautions in the work of three-ring medium-speed micro-grinding 1, often check the bearing temperature, if the temperature is too high, should check the lubrication and transmission parts are normal, rolling distance is too tight.

Find out the cause in a timely manner, take appropriate measures, in serious cases should be stopped inspection.

2, often check the degree of tension of the transmission belt, belt too loose will reduce the transmission efficiency and affect the grinding effect, too tight is easy to cause bearing heat, increase power consumption, reduce the service life of the belt.

3, all kinds of transmission components must be fastened reliable, removal or installation should use special tools, do not use hammers and other tools directly hit. 4, do not forget to check the pneumatic components, plastic grinding machine boot, to often check the air way in the pneumatic components, air routes and connections whether there is air leakage or damage, at the same time to check whether the gas supply pressure meets the requirements, the use of synchronous belt should also be checked frequently, if found too tight, too loose, beat, run-off, wear serious, should be adjusted in time, Repair or replacement. The amount of oil in the gas-source triummetry is checked regularly, and 20 s ingot oil must be added to avoid blockage in the pipe holes.